Do you have a minute to answer an electric vehicle survey? Start the survey | No thanks

Audi Coupe MOT Results

69.5% pass rate
from 275 tests in 2020
Failure rates by item

Here you can drill down into the failure rates for each item on the test. We've also compared the rates to the average results for pre-1990 cars and highlighted areas where the Audi Coupe is unusually good or bad.

  • 17% fail on Lamps, reflectors and electrical equipment
    • 4.4% fail on Direction indicators
      • 4.4% fail on Flashing type
        • 2.2% fail on Side repeaters (2 times worse than other pre-1990 cars)
        • 1.8% fail on Individual direction indicators
        • 0.36% fail on All direction indicators
    • 4.0% fail on Headlamp aim
      • 3.6% fail on Headlamp aim
      • 0.36% fail on Headlamp aim not tested
    • 4.0% fail on Front and rear fog lamps
      • 4.0% fail on Rear fog lamp
        • 4.0% fail on Rear fog lamp
    • 3.3% fail on Position lamps
      • 2.9% fail on Position lamp
      • 0.36% fail on Switch
    • 3.3% fail on Stop lamp
    • 2.9% fail on Electrical equipment
      • 1.8% fail on Horn
      • 0.73% fail on Battery(ies)
      • 0.36% fail on Electrical wiring
    • 2.2% fail on Headlamps
      • 2.2% fail on Headlamp
    • 1.5% fail on Registration plate lamp(s)
    • 1.5% fail on Mandatory tell-tales (2 times worse than other pre-1990 cars)
      • 1.5% fail on Rear fog lamp tell-tale (4 times worse than other pre-1990 cars)
  • 13% fail on Brakes
    • 9.8% fail on Brake performance
      • 4.0% fail on Parking brake efficiency (sp)
        • 3.6% fail on Rbt (sp)
        • 0.36% fail on Decelerometer (sp)
      • 3.3% fail on Parking brake performance (170% worse than other pre-1990 cars)
        • 3.3% fail on Rbt (170% worse than other pre-1990 cars)
          • 2.9% fail on Parking brake performance (2 times worse than other pre-1990 cars)
          • 0.36% fail on Parking (secondary brake performance)
      • 2.9% fail on Service Brake Efficiency (sp)
        • 2.9% fail on Rbt (sp)
          • 2.5% fail on Service brake imbalance
          • 1.8% fail on Service brake performance
      • 2.5% fail on Service brake performance
        • 2.5% fail on Rbt
          • 2.2% fail on Service brake performance
          • 0.36% fail on Service brake imbalance
      • 1.1% fail on Brake performance not tested
    • 1.5% fail on Rigid brake pipes
    • 1.1% fail on Parking brake control
      • 1.1% fail on Lever
    • 1.1% fail on ABS / EBS / ESC (7 times worse than other pre-1990 cars)
      • 1.1% fail on Anti-lock braking system (7 times worse than other pre-1990 cars)
    • 0.73% fail on Service brake pedal or hand lever
      • 0.73% fail on Pedal
    • 0.73% fail on Brake actuators (including spring brakes or hydraulic cylinders)
      • 0.36% fail on Hydraulic brake callipers
      • 0.36% fail on Hydraulic brake cylinder
    • 0.73% fail on Load sensing valves (8 times worse than other pre-1990 cars)
    • 0.36% fail on Hand operated control valves
      • 0.36% fail on Leaks
    • 0.36% fail on Hydraulic systems
      • 0.36% fail on Valves
    • 0.36% fail on Flexible brake hoses
  • 9.8% fail on Body, chassis, structure
    • 3.6% fail on Exhaust system
    • 2.9% fail on Transmission
      • 2.9% fail on Drive shafts (170% worse than other pre-1990 cars)
        • 2.9% fail on Joints (180% worse than other pre-1990 cars)
    • 1.5% fail on Seats
      • 1.5% fail on Driver's seat
    • 1.1% fail on Fuel system
      • 1.1% fail on Pipe
      • 0.36% fail on Hose
    • 0.73% fail on Integral vehicle structure
      • 0.73% fail on Integral vehicle structure condition
    • 0.36% fail on Floor
    • 0.36% fail on Boot lid
      • 0.36% fail on Boot lid condition
    • 0.36% fail on Cabs
      • 0.36% fail on Prescribed areas
  • 9.5% fail on Suspension
    • 3.3% fail on Wheel bearings
    • 2.5% fail on Component mounting prescribed areas
    • 2.2% fail on Suspension arms
      • 1.1% fail on Pins and bushes
      • 1.1% fail on Ball joint
    • 1.1% fail on Sub-frames
      • 0.36% fail on Sub-frame
      • 0.36% fail on Attachment bracket and mounting
      • 0.36% fail on Sub-frame mounting prescribed areas
    • 0.36% fail on Shock absorbers
    • 0.36% fail on Macpherson strut
      • 0.36% fail on Pins and bushes
    • 0.36% fail on Suspension rods
      • 0.36% fail on Ball joint dust cover
    • 0.36% fail on Anti-roll bars
      • 0.36% fail on Linkage pins and bushes
  • 3.3% fail on Visibility
    • 1.8% fail on Wipers
    • 1.8% fail on Washers
  • 2.9% fail on Noise, emissions and leaks
    • 2.9% fail on Exhaust emissions
      • 2.9% fail on Spark ignition
        • 2.2% fail on Non catalyst emissions
        • 0.73% fail on Emissions not tested
  • 1.1% fail on Identification of the vehicle
    • 1.1% fail on Registration plates
  • 1.1% fail on Steering
    • 0.36% fail on Steering linkage components
      • 0.36% fail on Track rod end
    • 0.36% fail on Steering column
    • 0.36% fail on Steering play
      • 0.36% fail on Steering rack
  • 1.1% fail on Seat belts and supplementary restraint systems
    • 1.1% fail on Seat belts
      • 1.1% fail on Prescribed areas
  • 1.1% fail on Tyres
    • 0.73% fail on Condition
    • 0.36% fail on Tread depth
  • 0.73% fail on Road Wheels
    • 0.73% fail on Attachment